Thickness: 0.1-200mm or as requirement, or as customer’s requirements.
Width: 50mm-2500mm, or as customer’s requirements.
Length: 50mm-8000mm, or as customer’s requirements.
Material: 1050, 1060, 1070, 1080, 1100, 1235, 2011, 2014, 2017, 2024, 2A12, 2A16, 2A06, 3002, 3003, 3004, 3004, 3104, 3204, 3030, 3A21, 5005, 5025, 5040, 5052, 5056, 5083, 5086, 5182, 5754, 5A05, 6003, 6060, 6061, 6082, 6083, 6063, 6061, 7003, 8006, 8011, 8021, 8079.
Standard: JIS, AISI, ASTM, GB, DIN, EN, etc.
Stock: 8000 Ton/Month.
Quality control: Third Part Inspection is acceptable.
Delivery Time: Within 3 days for our stock size, 15-20days for our production.
Aluminum sheet is a very common material with good forming performance, corrosion resistance, weld-ability and medium strength. It is widely used to make airplane oil tank, oil pipe, as well as the transportation vehicles, ships’ metal parts, instrument, lamps stent and rivet, metal products, electrical enclosure, etc.
5005 aluminum sheet belongs to 5-series Al-Mg alloy, but the content of the main alloy Mg is less than that of other 5-series alloy sheets, so it has a slightly higher corrosion resistance than the 3-series alloy. Among them, the performance of 5005 aluminum alloy is similar to that of 3 series 3003 aluminum alloy, with moderate strength, good fusion, processing and formability, but its anodic oxidation effect is better than that of 3003 aluminum alloy, the oxide film is brighter, and can achieve the same color as that of 6063 alloy! Therefore, 5005 aluminum sheet is commonly used for high-end wide-format curtain wall panels, architectural ornaments, vehicle interior materials, instrument panel, oxidizing materials, cooking utensils, conductors and other aspects.
| Product name | 5005 Aluminum sheet |
| Material | 1000 Series:1050,1060,1071,1080,1100,1435,etc. 2000 Series:2011,2014,2017,2024,2A12,2A16,2A06,etc. 3000 Series:3002,3003,3004,3104,3204,3030,3A21,etc. 4000 Series:4A01 5000 Series:5005,5025,5040,5052,5056,5083,5A05,5754, etc. 6000 Series:6003,6060, 6061, 6082,6083,6063,6061,etc. 7000 Series:7003,7005,7050,7075, 7085etc. |
| Standard | ASTM, JIS, SUS, EN, DIN, GB, etc. |
| Thickness | Sheet: 0.1 mm- 2.0mm Normal sheet: 0.15 mm- 2.0mm Medium plate: 6.0 mmt-25.0mm Plate: 25mm-200mm Super thick plate: more than 200mm |
| Width | 50mm-2500mm or as the customer’s request |
| Length | 50mm-8000mm or as the customer’s request |
| Surface | Oxidation, embossed, mill, bright, polished, hair line, brush, sand blast, checkered, etc. |
| OEM Service | Perforated, cutting special size, doing flatness, surface treatment, etc |
| Delivery Time | Within 3 days for our stock size,15-20days for our production |
| MOQ | 5 Ton |
| Sample | Free and available |
| Packaging | Export standard package: bundled wooden box, suit for all kinds of transport, or be required. |
| Container Size | 20ft GP: 5898MM(Length)*2352mm(Width)*2393mm(High) 40ft GP:12032mm(Length)*2352mm(Width)*2393mm(High) 40ft HC:12032mm(Length)*2352mm(Width)*2393mm(High) |
| Application | Construction, decoration, hardware, electric appliances, machinery and other industrial andcivil purposes, sucaselectroniccapacitor, compositecooker, rice cooker, refrigerator, computercasting, telecommunication, equipment, lampshade, air conditioner, cosmetics coverand so on. |
| 5005 Chemical Composition | |||||||||
| Al | Si | Cu | Mg | Zn | Mn | Cr | Ni | Ti | Fe |
| Margin | ≤0.30 | ≤0.20 | 0.50-1.10 | ≤0.25 | ≤020 | ≤0.10 | --- | --- | ≤0.70 |
| 5005 Mechanical Property | |||
| Tensile Strength (Mpa) |
Yield strength (Mpa) |
EL (%) |
Density (g/cm³) |
| 155-195 | ≥125 | ≥2% | 2.75 |
1. Medium Intensity. Similarly, 5005 aluminum sheet is a non-heat-treated alloy that is cold-machined to improve its strength.
2. Good Formability. Under the condition of hardening or annealing in semi-cold working, the plasticity of 5005 aluminum alloy is good, but in cold working, the strength increases, and the plasticity is low.
3. Excellent Weather Resistance. The strength of 5005 aluminum sheet, whose surface is treated by anodic oxidation, will not decrease with the decrease of temperature. No low temperature brittleness occurs.
4. Physical Properties. 5005 aluminum tensile strength σb(MPa) is 100~205, elongation δ110 (%) is 1~8.
1. Cracks, corrosion spots and traces of nitrate are not allowed on the surface.
2. Peeling, bubbles, surface roughness and local mechanical damage with depth less than 8% of the nominal wall thickness of the defect location are allowed on the surface, but the maximum depth of the defect shall not exceed 0.5mm, and the total area of the defect shall not exceed 5% of the total area of the plate.
3. The supplier is allowed to polish the profile longitudinally until the surface is smooth.
4. Other requirements: prepared by the demander and the supplier.
5. The surface of the aluminum plate is bright, without scratches, and the plates pressed out by the machine are few.
We are factory and have plenty of inventory, can meet various needs.
5005 Aluminum Sheet for Curtain Wall
5005 aluminum sheet can be used as high-end wide-format curtain wall material, which has the advantage of excellent anodic oxidation effect compared with the commonly used 3003 aluminum sheet for curtain wall. In addition, 5005 aluminum alloy is light, only one fifth of the marble, one third of the glass curtain wall, and can be perfectly combined with the glass and stone curtain wall material, presenting a fashion, trend, unique modern architectural style. It is worth mentioning that, the cost-effective price, as well as the low maintenance cost in the later period, make the architects more favor to the 5005 aluminum sheet!
Other Usages
Besides, 5005 aluminum sheet is also commonly used for building decoration parts, vehicle interior materials, instrument panel, oxidizing materials, cooking utensils, conductors and other manufacturing.
1. Standard seaworthy export packing, wooden pallets with plastics protection for the coil and sheet;
2. 15-20MT can be loaded into 20’container and 21-24MT is more suitable in 40’container;
3. The other packing can be made based on the customer requirement;
4. Normally, we have four layers of packing: wooden pallets, hardboard, Kraft paper and plastic. And fill more desiccants into package;
5. Eye to wall or eye to sky for coils.
We are factory wholesale price, and the prices are lower than 95% of suppliers. Our professional quotation will help you with your project. Expecting our long-term cooperation. ）
